Routing problem on GPSMAP 276Cx

Hi all might be i stumbled again over a silly problem on my GPSMAP 276Cx. Try to route from my Hometown Hürtgenwald to Bad Honnef. The most obvious way to do that is using the ferry Rolandseck <-> Bad Honnef. MapSource will use it but it seems, that the Garmin Device refuse to use any ferry routing, it chooses always a routing using bridges. Any idea, what could be wrong ? -- Mit freundlichen Grüßen ##################################################### Manfred Haiduk, Zum Fischbach 9, 52393 Hürtgenwald e-mail mhaiduk@t-online.de #####################################################

Hi Manfred, did you make sure that the transport mode on your device is configured to allow usage of ferries? Gerd ________________________________________ Von: mkgmap-dev <mkgmap-dev-bounces@lists.mkgmap.org.uk> im Auftrag von Manfred Haiduk <mhaiduk@t-online.de> Gesendet: Sonntag, 11. Oktober 2020 19:26 An: Development list for mkgmap Betreff: [mkgmap-dev] Routing problem on GPSMAP 276Cx Hi all might be i stumbled again over a silly problem on my GPSMAP 276Cx. Try to route from my Hometown Hürtgenwald to Bad Honnef. The most obvious way to do that is using the ferry Rolandseck <-> Bad Honnef. MapSource will use it but it seems, that the Garmin Device refuse to use any ferry routing, it chooses always a routing using bridges. Any idea, what could be wrong ? -- Mit freundlichen Grüßen ##################################################### Manfred Haiduk, Zum Fischbach 9, 52393 Hürtgenwald e-mail mhaiduk@t-online.de ##################################################### _______________________________________________ mkgmap-dev mailing list mkgmap-dev@lists.mkgmap.org.uk http://www.mkgmap.org.uk/mailman/listinfo/mkgmap-dev

Hi Also: Routes through ferry terminals often involve service roads with a low road-class. Fastest time routing avoids using lower class roads in the middle of a journey. Again, in a terminal there are often barriers and roads marked as access=customer or similar and these might set mkgmap:throughroute=no, again preventing routing. In complex terminals, there often isn't a clear route through onto the ferry - I spent a while examining the terminals at both ends of a ferry and fixing various one-ways etc. Finally, after the doing the above, I still couldn't make this particular ferry work. Changing the ferry to a standard road didn't fix it. I could route from just outside one terminal to just outside the terminal at the other end, but not to points further along the road. I think there might be a problem with the internal routing structures (RouteCenter) where there is a single long distance as the only connection within a RouteCenter and this is also the only connection between the other RouteCenters at either end. Ticker On Tue, 2020-10-13 at 07:19 +0000, Gerd Petermann wrote:
Hi Manfred,
did you make sure that the transport mode on your device is configured to allow usage of ferries?
Gerd
________________________________________ Von: mkgmap-dev <mkgmap-dev-bounces@lists.mkgmap.org.uk> im Auftrag von Manfred Haiduk <mhaiduk@t-online.de> Gesendet: Sonntag, 11. Oktober 2020 19:26 An: Development list for mkgmap Betreff: [mkgmap-dev] Routing problem on GPSMAP 276Cx
Hi all
might be i stumbled again over a silly problem on my GPSMAP 276Cx. Try to route from my Hometown Hürtgenwald to Bad Honnef. The most obvious way to do that is using the ferry Rolandseck <-> Bad Honnef. MapSource will use it but it seems, that the Garmin Device refuse to use any ferry routing, it chooses always a routing using bridges. Any idea, what could be wrong ?
--
Mit freundlichen Grüßen
##################################################### Manfred Haiduk, Zum Fischbach 9, 52393 Hürtgenwald e-mail mhaiduk@t-online.de #####################################################
_______________________________________________ mkgmap-dev mailing list mkgmap-dev@lists.mkgmap.org.uk http://www.mkgmap.org.uk/mailman/listinfo/mkgmap-dev _______________________________________________ mkgmap-dev mailing list mkgmap-dev@lists.mkgmap.org.uk http://www.mkgmap.org.uk/mailman/listinfo/mkgmap-dev

Disregard this e-mail, found out, what was going wrong ;-) Am 11.10.2020 um 19:26 schrieb Manfred Haiduk:
Hi all
might be i stumbled again over a silly problem on my GPSMAP 276Cx. Try to route from my Hometown Hürtgenwald to Bad Honnef. The most obvious way to do that is using the ferry Rolandseck <-> Bad Honnef. MapSource will use it but it seems, that the Garmin Device refuse to use any ferry routing, it chooses always a routing using bridges. Any idea, what could be wrong ?
-- ##################################################### Viele Grüße und 73 de Manfred Haiduk, DD8KQ e-mail mhaiduk@t-online.de dd8kq@gmx.de #####################################################
participants (4)
-
DD8KQ
-
Gerd Petermann
-
Manfred Haiduk
-
Ticker Berkin